Обзоры / Epson Error Codes 3

Главная / Обзоры / Epson Error Codes 3

 Epson 4xx0 Error Codes

 
Maintenance Requests Errors
MAINTENANCE REQ - 0002 - The number of CR movement cycles has reached predetermined value
MAINTENANCE REQ - 0008 - RTC backup battery shut off
MAINTENANCE REQ - 0040 - Pump counter has reached predetermined amount.
MAINTENANCE REQ - 0080 - Date is not set
MAINTENANCE REQ - 0088 - RTC backup battery is not installed.
MAINTENANCE REQ - 0100 - RTC backup battery pressure is temporally low.
MAINTENANCE REQ - 0200 - The number of ASF paper feeding has reached predetermined value.
 
Service Request Errors
SERVICE REQ - 00000101 - CR Motor life
SERVICE REQ - 00010000 - PF Motor Encoder check error
SERVICE REQ - 00010001 - PF Motor out of step
SERVICE REQ - 00010002 - PF Motor over current
SERVICE REQ - 00010003 - PF Motor in-position time-out
SERVICE REQ - 00010004 - CR Motor Encoder check error
SERVICE REQ - 00010005 - CR Motor out of step
SERVICE REQ - 00010006 - CR Motor over current
SERVICE REQ - 00010007 - CR Motor in-position time-out
SERVICE REQ - 00010008 - Servo interrupt watchdog time-out
SERVICE REQ - 00010009 - System interrupt watchdog time-out
SERVICE REQ - 0001000A - CR axis detection error
SERVICE REQ - 0001000C - PG axis detection error
SERVICE REQ - 0001000F - CR Motor PWM output faulty
SERVICE REQ - 00010010 - PF Motor PWM output faulty
SERVICE REQ - 00010012 - CR overload (high sensitivity) error
SERVICE REQ - 00010013 - PR overload (high sensitivity) error
SERVICE REQ - 0001001B - Head driver (TG) temperature error
SERVICE REQ - 0001001D - CR servo parameter error
SERVICE REQ - 0001001E - PF servo parameter error
SERVICE REQ - 00010020 - CSIC reed/right error
SERVICE REQ - 00010022 - Ink type error (setting on printer body side)
SERVICE REQ - 00010023 - RTC analysis error
SERVICE REQ - 00010025 - CSIC ROM communication error
SERVICE REQ - 00010026 - RTC communication error
SERVICE REQ - 00010028 - Head error
SERVICE REQ - 00010029 - Unidentified NMI
SERVICE REQ - 0001002A - CR ASIC ECU error
SERVICE REQ - 0001002B - PF ASIC ECU error
SERVICE REQ - 0001002D - Cleaning Unit work life error
SERVICE REQ - 0001002F - 360 DPI writing time out error
SERVICE REQ - 00010030 - Multi Sensor failure
SERVICE REQ - 00010031 - ASF phase detection error
SERVICE REQ - 00010032 - ASF drive switch error
SERVICE REQ - 00010033 - Eject phase detection error
SERVICE REQ - 00010034 - Eject movement error
SERVICE REQ - 00010035 - Pump phase detection error
SERVICE REQ - 00010036 - Type-B board installation error
SERVICE REQ - 00010037 - Head thermistor error
SERVICE REQ - 00010038 - Transistor thermistor error
SERVICE REQ - 00010039 - PG adjustment value incorrect overwrite error
SERVICE REQ - 0001003A - PG adjustment value outside range error
SERVICE REQ - 0001003B - Cutter installation error 1
SERVICE REQ - 0001003C - Cutter installation error 2
SERVICE REQ - 0001003D - Cutter installation error 3
SERVICE REQ - 00020000 - NVRAM error
SERVICE REQ - 00020002 - SDRAM error
SERVICE REQ - 00020003 - BOOT program SUM error
SERVICE REQ - 00020009 - Flash memory SUM error
SERVICE REQ - 0002000A - Program load error
SERVICE REQ - 0002000B - Internal memory shortage error
SERVICE REQ - 100000E0 - CPU address error (load misalignment)
SERVICE REQ - 10000100 - CPU address error (storage misalignment)
SERVICE REQ - 10000180 - CPU reserve command code exception error
SERVICE REQ - 100001A0 - CPU slot illegal command exception error
SERVICE REQ - 100001C0 - AC disruption
SERVICE REQ - 100005C0 - CPU DMA address error
SERVICE REQ - 10000xxx - CPU error
SERVICE REQ - 0003xxxx - Debug error code
SERVICE REQ - 0Dxxxxxx - Debug error code
SERVICE REQ - 0Exxxxxx - RTC timer off error
 
Epson 4000 Error Codes
 
Maintenance Requests Errors
MAINTENANCE REQ - 0002 - The number of CR movement cycles has reached predetermined value
MAINTENANCE REQ - 0008 - RTC backup battery shut off
MAINTENANCE REQ - 0040 - Pump counter has reached predetermined amount.
MAINTENANCE REQ - 0080 - Date is not set
MAINTENANCE REQ - 0088 - RTC backup battery is not installed.
MAINTENANCE REQ - 0100 - RTC backup battery pressure is temporally low.
MAINTENANCE REQ - 0200 - The number of ASF paper feeding has reached predetermined value.
 
Service Request Errors
SERVICE REQ - 00000101 - CR Motor life
SERVICE REQ - 00010000 - PF Motor Encoder check error
SERVICE REQ - 00010001 - PF Motor out of step
SERVICE REQ - 00010002 - PF Motor over current
SERVICE REQ - 00010003 - PF Motor in-position time-out
SERVICE REQ - 00010004 - CR Motor Encoder check error
SERVICE REQ - 00010005 - CR Motor out of step
SERVICE REQ - 00010006 - CR Motor over current
SERVICE REQ - 00010007 - CR Motor in-position time-out
SERVICE REQ - 00010008 - Servo interrupt watchdog time-out
SERVICE REQ - 00010009 - System interrupt watchdog time-out
SERVICE REQ - 0001000A - CR axis detection error
SERVICE REQ - 0001000C - PG axis detection error
SERVICE REQ - 0001000F - CR Motor PWM output faulty
SERVICE REQ - 00010010 - PF Motor PWM output faulty
SERVICE REQ - 0001001B - Head driver (TG) temperature error
SERVICE REQ - 0001001D - CR servo parameter error
SERVICE REQ - 0001001E - PF servo parameter error
SERVICE REQ - 00010020 - CSIC reed/right error
SERVICE REQ - 00010022 - Ink type error (setting on printer body side)
SERVICE REQ - 00010023 - RTC analysis error
SERVICE REQ - 00010025 - CSIC ROM communication error
SERVICE REQ - 00010026 - RTC communication error
SERVICE REQ - 00010028 - Head error
SERVICE REQ - 00010029 - Unidentified NMI
SERVICE REQ - 00001002A - CR ASIC ECU error
SERVICE REQ - 0001002B - PF ASIC ECU error
SERVICE REQ - 0001002D - Cleaning Unit work life error
SERVICE REQ - 0001002F - 360 DPI writing time out error
SERVICE REQ - 00010030 - Multi Sensor failure
SERVICE REQ - 00010031 - ASF phase detection error
SERVICE REQ - 00010032 - ASF drive switch error
SERVICE REQ - 00010033 - Eject phase detection error
SERVICE REQ - 00010034 - Eject movement error
SERVICE REQ - 00010035 - Pump phase detection error
SERVICE REQ - 00010036 - Type-B board installation error
SERVICE REQ - 00010037 - Head thermistor error
SERVICE REQ - 00010038 - Transistor thermistor error
SERVICE REQ - 00010039 - PG adjustment value incorrect overwrite error
SERVICE REQ - 0001003A - PG adjustment value outside range error
SERVICE REQ - 0001003B - Cutter installation error 1
SERVICE REQ - 0001003C - Cutter installation error 2
SERVICE REQ - 0001003D - Cutter installation error 3
SERVICE REQ - 00020000 - NVRAM error
SERVICE REQ - 00020002 - SDRAM error
SERVICE REQ - 00020003 - BOOT program SUM error
SERVICE REQ - 00020009 - Flash memory SUM error
SERVICE REQ - 0002000A - Program load error
SERVICE REQ - 0002000B - Internal memory shortage error
SERVICE REQ - 100000E0 - CPU address error (load misalignment)
SERVICE REQ - 10000100 - CPU address error (storage misalignment)
SERVICE REQ - 10000180 - CPU reserve command code exception error
SERVICE REQ - 100001A0 - CPU slot illegal command exception error
SERVICE REQ - 100001C0 - AC disruption
SERVICE REQ - 100005C0 - CPU DMA address error
SERVICE REQ - 10000xxx - CPU error
SERVICE REQ - 0003xxxx - Debug error code
SERVICE REQ - 0Dxxxxxx - Debug error code
 
Epson 10000 10600 Error Codes
 
Maintenance Requests Errors
MAINTENANCE REQ - 0100 - Indicates small quantity of remaining waste ink material absorption.
MAINTENANCE REQ - 0101 - The CR motor reached the 3% remaining to the life.
MAINTENANCE REQ - 0102 - Auto nozzle check error
MAINTENANCE REQ - 0103 - Backup battery for RTC (real time clock) life expired.
MAINTENANCE REQ - 0104 - Dot missing detector error
 
Service Request Errors
SERVICE REQ - 00000100 - Waste ink pads are full
SERVICE REQ - 00000101 - CR motor life (Ink tubes also reached their life)
SERVICE REQ - 00000102 - Nozzle check error compulsory continuity
SERVICE REQ - 00000103 - RTC backup battery end
SERVICE REQ - 00000104 - Auto print head optimization system
SERVICE REQ - 00000105 - Head unit life end
SERVICE REQ - 00000106 - Cleaning unit life end
SERVICE REQ - 00010000 - PF motor/ encoder check error
SERVICE REQ - 00010001 - PF motor step-out
SERVICE REQ - 00010002 - PF motor/overcurrent
SERVICE REQ - 00010003 - PF motor/ in position time-out error
SERVICE REQ - 00010004 - CR motor/ encoder check error
SERVICE REQ - 00010005 - CR motor step-out
SERVICE REQ - 00010006 - CR motor/overcurrent
SERVICE REQ - 00010007 - CR motor/ in position time-out error
SERVICE REQ - 00010008 - Servo interruption watch dog time out error
SERVICE REQ - 00010009 - System interruption watch dog time out error
SERVICE REQ - 0001000A - CR origin sensor mulfanction
SERVICE REQ - 0001000B - PF origin sensor mulfanction
SERVICE REQ - 0001000C - HS origin sensor mulfanction
SERVICE REQ - 0001000D - Cover sensor mulfanction
SERVICE REQ - 0001000E - Cover sensor mulfanction
SERVICE REQ - 0001000F - CR motor over heat (PWM output malfunction)
SERVICE REQ - 00010010 - PF motor over heat (PWM output malfunction)
SERVICE REQ - 00010011 - Paper jam error
SERVICE REQ - 00010012 - Cap origin error
SERVICE REQ - 00010013 - Providing system origin error
SERVICE REQ - 00010014 - Pressurization error
SERVICE REQ - 00010015 - Liquid sensor overflow (K)
SERVICE REQ - 00010016 - Liquid sensor overflow©
SERVICE REQ - 00010017 - Liquid sensor overflow (M)
SERVICE REQ - 00010018 - Liquid sensor overflow (LC)
SERVICE REQ - 00010019 - Liquid sensor overflow (LM)
SERVICE REQ - 0001001A - Liquid sensor overflow (Y)
SERVICE REQ - 0001001B - Head driver (TG) temperature error
SERVICE REQ - 0001001C - FS origin (Suction fan shutter home position) error
SERVICE REQ - 0001001D - CR servo parameter error
SERVICE REQ - 0001001E - PF servo parameter error
SERVICE REQ - 00010020 - CSIC card read/write error
SERVICE REQ - 00010021 - Starter cartridge error
SERVICE REQ - 00010022 I- nk type NVRAM status error
SERVICE REQ - 00010023 - RTC operation malfunction
SERVICE REQ - 00010024 - Module communication time-out error
SERVICE REQ - 00010025 - CSIC EEROR access error
SERVICE REQ - 00010026 - RTC access error
SERVICE REQ - 00010027 - Pressure pump small leak error
SERVICE REQ - 00010028 - During cleaning, pressure pump small leak error
SERVICE REQ - 00020000 - NVRAM error
SERVICE REQ - 00020001 - NVRAM check sum error
SERVICE REQ - 00020002 - SDRAM error
SERVICE REQ - 00020003 - Flash memory sum error
SERVICE REQ - 00020004 - ASIC illegal version error
SERVICE REQ - 00020005 - Firmware ASIC mismatching error (Version:A)
SERVICE REQ - 00020006 - Firmware ASIC mismatching error (Version:B)
SERVICE REQ - 00020007 - Head/ASIC mismatch error
SERVICE REQ - 00020009 - Flash memory check sum error
SERVICE REQ - 0002000B - Memory insufficient error
SERVICE REQ - 0002000C - Review error
SERVICE REQ - 00030000 - 00030013 - Debug error
SERVICE REQ - 00030015 - Ink supply defective (K)
SERVICE REQ - 00030016 - Ink supply defective ©
SERVICE REQ - 00030017 - Ink supply defective (M)
SERVICE REQ - 00030018 - Ink supply defective (LC)
SERVICE REQ - 00030019 - Ink supply defective (LM)
SERVICE REQ - 0003001A - Ink supply defective (Y)
SERVICE REQ - 0003001B - GAP adjustment range error
SERVICE REQ - 0003001C - Timeout in case of no print finishing with ASIC
SERVICE REQ - D0120013 - Module comminication error
SERVICE REQ - D012001E - Engine side ASIC command transmission over flow
SERVICE REQ - D012001F - Engine side ASIC command receiption over error
SERVICE REQ - D0xxxxxx - Program error
SERVICE REQ - 10000E0 - CPU address error
SERVICE REQ - 1000100 - CPU address error
SERVICE REQ - 10000180 - CPU reservation instruction code exception error
SERVICE REQ - 100001A0 - CPU Slot unfair command exception error
SERVICE REQ - 100005C0 - CPU DMA address error
SERVICE REQ - 10000xxx - CPU illegal trap
SERVICE REQ - FFFFxxxx - OS kernel detection error 
<< вернуться к списку